nos_config - Manage Extreme Networks NOS configuration sections

New in version 2.7.

Synopsis

Parameters

Parameter Choices/Defaults Comments
after Default:
None
The ordered set of commands to append to the end of the command stack if a change needs to be made. Just like with before this allows the playbook designer to append a set of commands to be executed after the command set.
backup
bool
    Choices:
  • no ←
  • yes
This argument will cause the module to create a full backup of the current running-config from the remote device before any changes are made. The backup file is written to the backup folder in the playbook root directory. If the directory does not exist, it is created.
before Default:
None
The ordered set of commands to push on to the command stack if a change needs to be made. This allows the playbook designer the opportunity to perform configuration commands prior to pushing any changes without affecting how the set of commands are matched against the system.
diff_against
    Choices:
  • running
  • intended
When using the ansible-playbook --diff command line argument the module can generate diffs against different sources.
When this option is configured as intended, the module will return the diff of the running-config against the configuration provided in the intended_config argument.
When this option is configured as running, the module will return the before and after diff of the running-config with respect to any changes made to the device configuration.
diff_ignore_lines
Use this argument to specify one or more lines that should be ignored during the diff. This is used for lines in the configuration that are automatically updated by the system. This argument takes a list of regular expressions or exact line matches.
intended_config
The intended_config provides the master configuration that the node should conform to and is used to check the final running-config against. This argument will not modify any settings on the remote device and is strictly used to check the compliance of the current device's configuration against. When specifying this argument, the task should also modify the diff_against value and set it to intended.
lines Default:
None
The ordered set of commands that should be configured in the section. The commands must be the exact same commands as found in the device running-config. Be sure to note the configuration command syntax as some commands are automatically modified by the device config parser.

aliases: commands
match
    Choices:
  • line ←
  • strict
  • exact
  • none
Instructs the module on the way to perform the matching of the set of commands against the current device config. If match is set to line, commands are matched line by line. If match is set to strict, command lines are matched with respect to position. If match is set to exact, command lines must be an equal match. Finally, if match is set to none, the module will not attempt to compare the source configuration with the running configuration on the remote device.
multiline_delimiter Default:
@
This argument is used when pushing a multiline configuration element to the NOS device. It specifies the character to use as the delimiting character. This only applies to the configuration action.
parents Default:
None
The ordered set of parents that uniquely identify the section or hierarchy the commands should be checked against. If the parents argument is omitted, the commands are checked against the set of top level or global commands.
replace
    Choices:
  • line ←
  • block
Instructs the module on the way to perform the configuration on the device. If the replace argument is set to line then the modified lines are pushed to the device in configuration mode. If the replace argument is set to block then the entire command block is pushed to the device in configuration mode if any line is not correct.
running_config Default:
None
The module, by default, will connect to the remote device and retrieve the current running-config to use as a base for comparing against the contents of source. There are times when it is not desirable to have the task get the current running-config for every task in a playbook. The running_config argument allows the implementer to pass in the configuration to use as the base config for comparison.

aliases: config
src Default:
None
Specifies the source path to the file that contains the configuration or configuration template to load. The path to the source file can either be the full path on the Ansible control host or a relative path from the playbook or role root directory. This argument is mutually exclusive with lines, parents.

Notes

Note

  • Tested against NOS 7.2.0

Examples

- name: configure top level configuration
  nos_config:
    lines: logging raslog console INFO

- name: configure interface settings
  nos_config:
    lines:
      - description test interface
      - ip address 172.31.1.1/24
    parents:
      - interface TenGigabitEthernet 104/0/1

- name: configure multiple interfaces
  nos_config:
    lines:
      - lacp timeout long
    parents: "{{ item }}"
  with_items:
    - interface TenGigabitEthernet 104/0/1
    - interface TenGigabitEthernet 104/0/2

- name: load new acl into device
  nos_config:
    lines:
      - seq 10 permit ip host 1.1.1.1 any log
      - seq 20 permit ip host 2.2.2.2 any log
      - seq 30 permit ip host 3.3.3.3 any log
      - seq 40 permit ip host 4.4.4.4 any log
      - seq 50 permit ip host 5.5.5.5 any log
    parents: ip access-list extended test
    before: no ip access-list extended test
    match: exact

- name: check the running-config against master config
  nos_config:
    diff_against: intended
    intended_config: "{{ lookup('file', 'master.cfg') }}"

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
backup_path
string
 when backup is yes
The full path to the backup file

Sample:
/playbooks/ansible/backup/[email protected]:26:34
commands
list
 always
The set of commands that will be pushed to the remote device

Sample:
['switch-attributes hostname foo', 'router ospf', 'area 0']
updates
list
 always
The set of commands that will be pushed to the remote device

Sample:
['switch-attributes hostname foo', 'router ospf', 'area 0']


Status

This module is flagged as preview which means that it is not guaranteed to have a backwards compatible interface.

Maintenance

This module is flagged as community which means that it is maintained by the Ansible Community. See Module Maintenance & Support for more info.

For a list of other modules that are also maintained by the Ansible Community, see here.

Author

  • Lindsay Hill (@LindsayHill)

Hint

If you notice any issues in this documentation you can edit this document to improve it.