exos_config - Manage Extreme Networks EXOS configuration sections

New in version 2.7.

Synopsis

Parameters

Parameter Choices/Defaults Comments
after Default:
None
The ordered set of commands to append to the end of the command stack if a change needs to be made. Just like with before this allows the playbook designer to append a set of commands to be executed after the command set.
backup
bool
    Choices:
  • no ←
  • yes
This argument will cause the module to create a full backup of the current running-config from the remote device before any changes are made. The backup file is written to the backup folder in the playbook root directory. If the directory does not exist, it is created.
before Default:
None
The ordered set of commands to push on to the command stack if a change needs to be made. This allows the playbook designer the opportunity to perform configuration commands prior to pushing any changes without affecting how the set of commands are matched against the system.
defaults
bool
    Choices:
  • no ←
  • yes
This argument specifies whether or not to collect all defaults when getting the remote device running config. When enabled, the module will get the current config by issuing the command show running-config all.
diff_against
    Choices:
  • running
  • startup
  • intended
When using the ansible-playbook --diff command line argument the module can generate diffs against different sources.
When this option is configure as startup, the module will return the diff of the running-config against the startup-config.
When this option is configured as intended, the module will return the diff of the running-config against the configuration provided in the intended_config argument.
When this option is configured as running, the module will return the before and after diff of the running-config with respect to any changes made to the device configuration.
diff_ignore_lines
Use this argument to specify one or more lines that should be ignored during the diff. This is used for lines in the configuration that are automatically updated by the system. This argument takes a list of regular expressions or exact line matches.
intended_config
The intended_config provides the master configuration that the node should conform to and is used to check the final running-config against. This argument will not modify any settings on the remote device and is strictly used to check the compliance of the current device's configuration against. When specifying this argument, the task should also modify the diff_against value and set it to intended.
lines Default:
None
The ordered set of commands that should be configured in the section. The commands must be the exact same commands as found in the device running-config. Be sure to note the configuration command syntax as some commands are automatically modified by the device config parser.

aliases: commands
match
    Choices:
  • line ←
  • strict
  • exact
  • none
Instructs the module on the way to perform the matching of the set of commands against the current device config. If match is set to line, commands are matched line by line. If match is set to strict, command lines are matched with respect to position. If match is set to exact, command lines must be an equal match. Finally, if match is set to none, the module will not attempt to compare the source configuration with the running configuration on the remote device.
replace
    Choices:
  • line ←
  • block
Instructs the module on the way to perform the configuration on the device. If the replace argument is set to line then the modified lines are pushed to the device in configuration mode. If the replace argument is set to block then the entire command block is pushed to the device in configuration mode if any line is not correct.
running_config Default:
None
The module, by default, will connect to the remote device and retrieve the current running-config to use as a base for comparing against the contents of source. There are times when it is not desirable to have the task get the current running-config for every task in a playbook. The running_config argument allows the implementer to pass in the configuration to use as the base config for comparison.

aliases: config
save_when
    Choices:
  • always
  • never ←
  • modified
  • changed
When changes are made to the device running-configuration, the changes are not copied to non-volatile storage by default. Using this argument will change that behavior. If the argument is set to always, then the running-config will always be copied to the startup-config and the modified flag will always be set to True. If the argument is set to modified, then the running-config will only be copied to the startup-config if it has changed since the last save to startup-config. If the argument is set to never, the running-config will never be copied to the startup-config. If the argument is set to changed, then the running-config will only be copied to the startup-config if the task has made a change.
src Default:
None
Specifies the source path to the file that contains the configuration or configuration template to load. The path to the source file can either be the full path on the Ansible control host or a relative path from the playbook or role root directory. This argument is mutually exclusive with lines.

Notes

Note

  • Tested against EXOS version 22.6.0b19

Examples

- name: configure SNMP system name
  exos_config:
    lines: configure snmp sysName "{{ inventory_hostname }}"

- name: configure interface settings
  exos_config:
    lines:
      - configure ports 2 description-string "Master Uplink"
    backup: yes

- name: check the running-config against master config
  exos_config:
    diff_against: intended
    intended_config: "{{ lookup('file', 'master.cfg') }}"

- name: check the startup-config against the running-config
  exos_config:
    diff_against: startup
    diff_ignore_lines:
      - ntp clock .*

- name: save running to startup when modified
  exos_config:
    save_when: modified

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
backup_path
string
 when backup is yes
The full path to the backup file

Sample:
/playbooks/ansible/backup/[email protected]:00:21
commands
list
 always
The set of commands that will be pushed to the remote device

Sample:
['create vlan "foo"', 'configure snmp sysName "x620-red"']
updates
list
 always
The set of commands that will be pushed to the remote device

Sample:
['switch-attributes hostname foo', 'router ospf', 'area 0']


Status

This module is flagged as preview which means that it is not guaranteed to have a backwards compatible interface.

Maintenance

This module is flagged as community which means that it is maintained by the Ansible Community. See Module Maintenance & Support for more info.

For a list of other modules that are also maintained by the Ansible Community, see here.

Author

  • Lance Richardson (@hlrichardson)

Hint

If you notice any issues in this documentation you can edit this document to improve it.