junos_lldp - Manage LLDP configuration on Juniper JUNOS network devices

New in version 2.4.

Synopsis

Requirements

The below requirements are needed on the host that executes this module.

  • ncclient (>=v0.5.2)

Parameters

Parameter Choices/Defaults Comments
active
bool
    Choices:
  • no
  • yes ←
Specifies whether or not the configuration is active or deactivated
hold_multiplier
Specify the number of seconds that LLDP information is held before it is discarded. The multiplier value is used in combination with the interval value.
interval
Frequency at which LLDP advertisements are sent (in seconds).
provider
Deprecated
Starting with Ansible 2.5 we recommend using connection: network_cli or connection: netconf.
For more information please see the Junos OS Platform Options guide.

A dict object containing connection details.
username
Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_USERNAME will be used instead.
host
required
Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
ssh_keyfile
Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_SSH_KEYFILE will be used instead.
timeout Default:
10
Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
password
Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_PASSWORD will be used instead.
port Default:
22
Specifies the port to use when building the connection to the remote device. The port value will default to the well known SSH port of 22 (for transport=cli) or port 830 (for transport=netconf) device.
state
    Choices:
  • present ←
  • absent
  • enabled
  • disabled
Value of present ensures given LLDP configuration is present on device and LLDP is enabled, for value of absent LLDP configuration is deleted and LLDP is in disabled state. Value enabled ensures LLDP protocol is enabled and LLDP configuration if any is configured on remote device, for value of disabled it ensures LLDP protocol is disabled any LLDP configuration if any is still present.
transmit_delay
Specify the number of seconds the device waits before sending advertisements to neighbors after a change is made in local system.

Notes

Note

  • This module requires the netconf system service be enabled on the remote device being managed.
  • Tested against vSRX JUNOS version 15.1X49-D15.4, vqfx-10000 JUNOS Version 15.1X53-D60.4.
  • Recommended connection is netconf. See the Junos OS Platform Options.
  • This module also works with local connections for legacy playbooks.
  • For information on using CLI and netconf see the Junos OS Platform Options guide
  • For more information on using Ansible to manage network devices see the Ansible Network Guide
  • For more information on using Ansible to manage Juniper network devices see https://www.ansible.com/ansible-juniper.

Examples

- name: Enable LLDP service
  junos_lldp:
    state: enabled

- name: Disable LLDP service
  junos_lldp:
    state: disabled

- name: Set LLDP parameters
  junos_lldp:
    interval: 10
    hold_multiplier: 5
    transmit_delay: 30
    state: present

- name: Delete LLDP parameters
  junos_lldp:
    interval: 10
    hold_multiplier: 5
    transmit_delay: 30
    state: absent

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
diff.prepared
string
when configuration is changed and diff option is enabled.
Configuration difference before and after applying change.

Sample:
[edit] + protocols { + lldp { + disable; + } + }


Status

This module is flagged as preview which means that it is not guaranteed to have a backwards compatible interface.

Maintenance

This module is flagged as network which means that it is maintained by the Ansible Network Team. See Module Maintenance & Support for more info.

For a list of other modules that are also maintained by the Ansible Network Team, see here.

Support

For more information about Red Hat’s support of this module, please refer to this Knowledge Base article

Author

  • Ganesh Nalawade (@ganeshrn)

Hint

If you notice any issues in this documentation you can edit this document to improve it.